麥斯3D線材成型機,東莞轉頭折彎機廠家

地址:東莞市常平鎮司馬鄉工業開發區松嶺

電話:(0769)83829622

傳真:(0769)83970016

您現在的位置:首頁 > 新聞資訊 > 公司新聞

你想知道線材成型機常見的故障都有哪些不?

作者:管理員 發布于:2019-09-09
無論在生產或使用過程中,設備故障都是正?,F象,只要能及時處理,因為使用時間長,零件之間的磨損越來越多,那么故障就會出現,事實上,及時解決問題是好的,那么我們來看看這線材折彎機常見的故障。
環顧工作現場,清除妨礙工作和交通的雜物。地面上不得有油污,以免滑倒。工件應堆放整齊、牢固,防止坍塌和傷害。
檢查線材成型機上的保護裝置是否完好無損。如果未安裝,則不允許駕駛。中頻彎管機應具有良好的接地和電絕緣,電壓應穩定。
檢查線材成型機的光滑部位,缺油無油時,加足油。
空試運行時,檢查機械運行是否正常,電氣開關是否松動,使用是否方便。一切正常后,再做一次作業。
數控線材成型機
兩個人同時工作時應該密切合作和協調。應指定專門人員操作開關。操作過程中不要和他人交談或大笑,以防誤操作。
機床啟動時,操作人員不得離開機床。
數控線材成型機運行時,任何人不得靠近彎管行程范圍,并建立保護警示標志。撬管子時要站穩,以免撬桿打滑傷人。操作員只能站在外面。
想要了解更多的線材成型機的相關資訊的http://www.seslicool.com/news
推薦炭黑、膠頭螺帽兩個產品!
英語特配
Whether in production or in use, equipment failure is a normal phenomenon, as long as it can be handled in time, because the use of long time, wear and tear between parts more and more, then the failure will occur, in fact, timely problem solving is good, then let's look at the common fault of wire bender.

Look around the work site and remove the debris that hinders work and traffic. There must be no oil on the ground so as not to slip. Workpieces should be stacked neatly and firmly to prevent collapse and damage.

Check whether the protective device on the wire forming machine is in good condition. Driving is not allowed if not installed. Medium frequency pipe bender should have good grounding and electrical insulation, and the voltage should be stable.

Check the smooth part of the wire forming machine. When oil is short or no oil, add enough oil.

During the empty test run, check whether the machine is running normally, whether the electrical switch is loose, and whether it is convenient to use. Do your homework again after everything is OK.

Two people should work in close cooperation and coordination at the same time. Specialized personnel should be designated to operate the switch. Don't talk or laugh with others during the operation in case of misoperation.

When the machine tool is started, the operator must not leave the machine tool.

When CNC wire forming machine is running, no one should be close to the elbow travel range and establish protection warning signs. Stand firm when prying pipes so as not to slip and hurt people. Operators can only stand outside.

For more information on wire forming machines, http://www.seslicool.com/news

Recommend carbon black, rubber head nuts two products!
文本標簽:

線材折彎機| 彈簧機| 網站地圖| xml地圖| 文章標簽| 粵ICP備18103077號-5

版權所有 Copyright(C)2018-2022 東莞麥斯數控設備有限公司

欧美xxxxzozo另类特级_强奷漂亮少妇同事_jrs低调看高清直播_激烈的性高湖波多野结衣